ASSEMBLY STEP 8
WATER BOWL INSTALLATION
1. Slide the Water Bowl into the lowest Rack position. FIGURE 14
2. Insert the Cooking Racks into the remaining Rack positions as desired; however,
do not insert a Grid directly over the Water Bowl - the Water Bowl will restrict
heat distribution. For best results, the Rack wires should run front to back.
3. Re-mount the Door Panel by sliding the Door’s hinge pins into the Cabinet’s
hinge seats.
FIGURE 14
ASSEMBLY STEP 9
HANDLE INSTALLATION
1. Slide the washer onto the end of the Door Handle, followed by the Spring. FIGURE 15
2. Feed the Door Handle into the hole through the front of the Door Panel. FIGURE 16
3. From the back side of the Door Panel, insert the Mounting Plate over the end
of the Door Handle.
FIGURE 16
4. With Lock Washers placed on the Bolts, insert the Bolts through the Mounting
Plate, into the pre-threaded mounts and rmly tighten the Bolts.
ASSEMBLY STEP 10
HEAT INDICATOR INSTALLATION
1. Remove the Nut from the back of the Temperature Gauge and insert
the Temperature Gauge into the Door Panel.
FIGURE 17 Make sure the
Temperature Gauge numbers are positioned right side up.
FIGURE 18
2. From the back side of the Door Panel, place the Washer on, then
thread the Nut onto the Temperature Gauge.
3. Tighten the Nut rmly, but do not over tighten.
ASSEMBLY STEP 11
NAMEPLATE INSTALLATION
1. Insert the Name Plate mounts through
the mounting holes in the front of the
Door Panel.
FIGURE 19
2. From the inside of the Door Panel,
securely attach the Push Nuts to the
Name Plate mounts.
ASSEMBLY STEP 12
SECURING THE HVR
1. Place one end of the S-Hook around
the HVR neck.
FIGURE 20
2. When an LP tank is not attached to the
Smoker, use the S-Hook to hang the
HVR from the Carry Handle on the
side of the Smoker.
This will help
prevent dirt and other particles
from plugging the end of the HVR.
ASSEMBLY IS NOW COMPLETE!
Please follow all instructions and
safeguards on the following pages for
connecting the LP tank.
-10- -11-
LOCATE THESE PARTS
WATER
BOWL
COOKING
RACKS
30” MODEL HAS 3 RACKS
36” MODEL HAS 4 RACKS
48” MODEL HAS 6 RACKS
WATER
BOWL
COOKING
RACKS
CABINET
FIGURE 14
Door
D
HARDWARE & PARTS
TOOLS NEEDED
HARDWARE BAG
PHILLIPS
HEAD
SCREWDRIVER
DOOR
HANDLE
Includes Spring & Washer
2 WASHERS
2 MOUNTING
PLATE
2 BOLTS
30” / 36” MODELS HAVE 1 HANDLE
48” MODEL HAS 2 HANDLES
FIGURE 15
FIGURE 16
DOOR
PANEL
DOOR
HANDLE
Repeat steps 1-4 for the 48” Smoker, as it will
have 2 Handles to install.
E
HARDWARE
TOOLS NEEDED
HARDWARE BAG
1/2” WRENCH
TEMPERATURE
GAUGE
NUT
NOTE: This Nut
is already threaded
onto the Temperature
Gauge and must be
removed for assembly.
WASHER
FIGURE 18
FIGURE 17
LOCATE THESE PARTS
FIGURE 19
NAMEPLATE
2 PUSH NUTS
FIGURE 20
F
LOCATE THESE PARTS
HARDWARE BAG
S-HOOK
(10 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals